# This is the N1KV VEM configuration file. # file contains all the configuration parameters for VEM operation. # Please find below a brief explanation of these parameters and their meaning. # Optional Parameters and Default Values of parameters are explicitly stated. # Note: # a)Mandatory parameters are needed for proper VEM operation. # N1KV DP/DPA should start even if these are not specified. # But there will be functional impact. For eg: in VSM connectivity # b)For any updates to parameters to take effect, you just need to execute # 'vemcmd reread config'. Its the least-disruptive way for changes to # take effect. However for certain params, n1kv service need to be restarted. # These parameter are stated explictly (restart_on_modify: YES). # # # # # TAG: switch-domain # Description: # Optional: No # Default: 1000 # restart_on_modify: No switch-domain <%= @n1kv_vsm_domain_id %> # TAG: l3control-ipaddr # Description: IP Address of VSM Mgmt I/F # Optional: No # Default: 127.0.0.1 # restart_on_modify: No l3control-ipaddr <%= @n1kv_vsm_ip %> # TAG: l3control-ipv6addr # Description: IPv6 Address of VSM Mgmt I/F # Optional: No # Default: ::1 # restart_on_modify: No l3control-ipv6addr <%= @n1kv_vsm_ipv6 %> # Set svs-mode to V6 if IPv6 address for VSM # is set to something other than default ::1. # This tells VEM to communicate with VSM on # IPv6 instead of the default IPv4 option <% if @n1kv_vsm_ipv6 != '::1' -%> svs-mode V6 <% end -%> # TAG: host-mgmt-intf # Description: Management interface of the Host # Optional: No (on N1KV, we need this # for Host Identification on VSM). # Default: lo # restart_on_modify: Yes host-mgmt-intf <%= @host_mgmt_intf %> # # Description: Port-Profile mapping for all VEM managed Interfaces. # Optional: Yes # restart_on_modify: No # # Note: Do not specify Host Management Interface here. # We do yet support System Ports (Ports which need to be up all time: Post Reboot/VEM Upgrade). # # Format for physical ports: # phys profile #phys eth1 profile sys-uplink #phys eth2 profile uplink2 <% @uplink_profile.each do |port, profile| -%> phys <%= port%> profile <%= profile%> <% end -%> # Format for non-vm virt ports. For instance: VTEP ports. # virt profile [mode static|dhcp] [address ] # [netmask ] [mac ] # [] -->indicates optional parameters. #Eg: #virt vtep3 profile profint mode dhcp #virt vtep1 profile profint mode dhcp mac 00:11:22:33:44:55 #virt vtep2 profile profint mode static address 192.168.2.91 netmask 255.255.255.0 #virt vtep2 profile profint mode static address 192.168.2.91 netmask 255.255.255.0 mac 00:22:22:33:44:55 <% @vtep_config.each do |port, params| -%> <% if params['ipmode'] == 'dhcp' -%> virt <%= port%> profile <%= params['profile']%> mode dhcp <% else-%> virt <%= port%> profile <%= params['profile']%> mode static address <%= params['ipaddress']%> netmask <%= params['netmask']%> <% end -%> <% end -%> # TAG: uvem-ovs-brname # Description: Default Open VSwitch Bridge Name # Optional: YES. # Default: n1kvdvs # restart_on_modify: Yes # Format: # uvem-ovs-brname n1kvdvs uvem-ovs-brname br-int # TAG: portdb # Description: PortDB (ovs|vem) # Optional: YES. # Default: ovs # restart_on_modify: Yes # Format: # portdb vem portdb <%= @portdb %> # TAG: node-type # Description: Type of Node: 'compute' (or) 'neutron' # Optional: YES. # Default: compute # restart_on_modify: No # Format: # node-type compute node-type <%= @node_type %> # The below parameters are not commonly modified. # # # # Description: System Port Profiles. # Optional: Yes (If there are no System Interfaces: Mgmt I/F etc) # restart_on_modify: No # #Trunk Profile Format #profile trunk #profile native-vlan #profile mtu # #Access Profile #profile access #profile mtu # TAG: dp-np-threads # Description: Number of datapath threads to process normal priority packets # Optional: YES # Default: 4 # restart_on_modify: Yes # Format: dp-np-threads <1..32> # TAG: dp-lp-threads # Description: Number of datapath threads to process low priority packets # Optional: YES # Default: 1 # restart_on_modify: Yes # Format: dp-lp-threads <1..32> # TAG: dp-hp-threads # Description: Number of datapath threads to process high priority packets # Optional: YES # Default: 1 # restart_on_modify: Yes # Format: dp-hp-threads <1..32> # TAG: dp-thread-sockets # Description: Number of packet sockets each datapath thread creates # Optional: YES # Default: 1 # restart_on_modify: Yes # Format: dp-thread-sockets <1..16> # TAG: dp-thread-socket-rbuflen # Description: Receive buffer length of each packet socket # Optional: YES # Default: 8 MBytes # restart_on_modify: Yes # Format: dp-thread-socket-rbuflen <0..255> # Note: 0 - use system default # TAG: dp-thread-socket-rrnglen # Description: Rx-ring length of each packet socket # Optional: YES # Default: 4096 # restart_on_modify: Yes # Format: dp-thread-socket-rrnglen <0..16384> # Note: 0 - disables memory map I/O # TAG: fastpath-flood # Description: Enable flood of broadcast and unknown pkts in KLM # Optional: YES # Default: disable # restart_on_modify: Yes # Format: fastpath-flood fastpath-flood <%= @fastpath_flood %>