kayobe/doc/source/development/automated.rst
Mark Goddard 02c1efe61a Change github URLs to git.openstack.org
It seems that a number of URLs in the documentation were not changed
following the switch to git.openstack.org.

Change-Id: If23f60ad04f77f9990bf229bc38c687106abeda6
2018-04-04 14:48:33 +01:00

4.9 KiB

Automated Setup

This section provides information on the development tools provided by kayobe to automate the deployment of various development environments.

For a manual procedure, see development-manual.

Overview

The kayobe development environment automation tooling is built using simple shell scripts. Some minimal configuration can be applied by setting the environment variables in dev/config.sh. Control plane configuration is typically provided via the dev-kayobe-config repository, although it is also possible to use your own kayobe configuration. This allows us to build a development environment that is as close to production as possible.

Environments

The following development environments are supported:

  • Overcloud (single OpenStack controller)
  • Seed hypervisor
  • Seed VM

The seed VM environment may be used in an environment already deployed as a seed hypervisor.

Overcloud

Preparation

Clone the kayobe repository:

git clone https://git.openstack.org/openstack/kayobe.git

Change the current directory to the kayobe repository:

cd kayobe

Clone the dev-kayobe-config repository to config/src/kayobe-config:

mkdir -p config/src
git clone https://github.com/stackhpc/dev-kayobe-config config/src/kayobe-config

Inspect the kayobe configuration and make any changes necessary for your environment.

If using Vagrant, follow the steps in development-vagrant to prepare your environment for use with Vagrant and bring up a Vagrant VM.

If not using Vagrant, the default development configuration expects the presence of a bridge interface on the OpenStack controller host to carry control plane traffic. The bridge should be named breth1 with a single port eth1, and an IP address of 192.168.33.3/24. This can be modified by editing config/src/kayobe-config/etc/kayobe/inventory/group_vars/controllers/network-interfaces. Alternatively, this can be added using the following commands:

sudo ip l add breth1 type bridge
sudo ip l set breth1 up
sudo ip a add 192.168.33.3/24 dev breth1
sudo ip l add eth1 type dummy
sudo ip l set eth1 up
sudo ip l set eth1 master breth1

Usage

If using Vagrant, SSH into the Vagrant VM and change to the shared directory:

vagrant ssh
cd /vagrant

If not using Vagrant, run the dev/install.sh script to install kayobe and its dependencies in a virtual environment:

./dev/install.sh

Run the dev/overcloud-deploy.sh script to deploy the OpenStack control plane:

./dev/overcloud-deploy.sh

Upon successful completion of this script, the control plane will be active.

Seed Hypervisor

The seed hypervisor development environment is supported for CentOS 7. The system must be either bare metal, or a VM on a system with nested virtualisation enabled.

Preparation

The following commands should be executed on the seed hypervisor.

Clone the kayobe repository:

git clone https://git.openstack.org/openstack/kayobe.git

Change the current directory to the kayobe repository:

cd kayobe

Clone the add-seed-and-hv branch of the dev-kayobe-config repository to config/src/kayobe-config:

mkdir -p config/src
git clone https://github.com/stackhpc/dev-kayobe-config -b add-seed-and-hv config/src/kayobe-config

Inspect the kayobe configuration and make any changes necessary for your environment.

Usage

Run the dev/install.sh script to install kayobe and its dependencies in a virtual environment:

./dev/install.sh

Run the dev/seed-hypervisor-deploy.sh script to deploy the seed hypervisor:

./dev/seed-hypervisor-deploy.sh

Upon successful completion of this script, the seed hypervisor will be active.

Seed VM

The seed VM should be deployed on a system configured as a libvirt/KVM hypervisor, using the kayobe seed hypervisor support or otherwise.

Preparation

The following commands should be executed on the seed hypervisor.

Change the current directory to the kayobe repository:

git clone https://git.openstack.org/openstack/kayobe.git

Change to the kayobe directory:

cd kayobe

Clone the add-seed-and-hv branch of the dev-kayobe-config repository to config/src/kayobe-config:

mkdir -p config/src
git clone https://github.com/stackhpc/dev-kayobe-config -b add-seed-and-hv config/src/kayobe-config

Inspect the kayobe configuration and make any changes necessary for your environment.

Usage

Run the dev/install.sh script to install kayobe and its dependencies in a virtual environment:

./dev/install.sh

Run the dev/seed-deploy.sh script to deploy the seed VM:

./dev/seed-deploy.sh

Upon successful completion of this script, the seed VM will be active. The seed VM may be accessed via SSH as the stack user:

ssh stack@192.168.33.5